headlight

**Sal** · 08-19-2004, 01:04 PM

Ok so i just installed my 4100k catz HID and they are not alligned properly but the h7 bulbs before were fine. Are you supposed to adjust them after installation or maybe some thing i did wrong. They only show the bulk of the light like 2 feet in front of the car.

**DaksGT** · 08-19-2004, 01:13 PM

You need washers. Most likely the burner is not sitting properly inside the housing.

**Sal** · 08-19-2004, 01:17 PM

It has like 4-5 rubber washer already on it. Trevor from VD installed them on the guy's car i bought them off.

**DaksGT** · 08-19-2004, 02:21 PM

Aim them then.

**Sal** · 08-19-2004, 06:41 PM

ya i figure it is the only option left. I just hate doing it aming out hjeadlights are a pain in the ass

**DaksGT** · 08-19-2004, 06:52 PM

Not at all, all you need is an 8mm and a wall.

**Sal** · 08-19-2004, 06:54 PM

ya but getting it down in ther is a tight fit I find using my fingers is the best.

I had to do my cuz's a while back and it was a pain in the ass

**TRD604** · 10-18-2004, 11:54 PM

im having problems aiming mine.

i used my fingers to turn the screw set thing. but didnt notice any changes

**TRD604** · 10-19-2004, 12:15 AM

nevermind...all fixed now..

08-19-2004, 01:04 PM	#1 (permalink)
Sal Location: Windsor Posts: 2,231 Join Date: Oct 2003 Last On: 11-21-2008 04:46 PM Vehicle: 07 Dakota 2nd Vehicle: 02 Celica GTS	headlight Ok so i just installed my 4100k catz HID and they are not alligned properly but the h7 bulbs before were fine. Are you supposed to adjust them after installation or maybe some thing i did wrong. They only show the bulk of the light like 2 feet in front of the car. __________________ Let it not be said dat I iz a man dat does not care.

08-19-2004, 01:13 PM	#2 (permalink)
DaksGT Location: Monaco Posts: 5,023 Join Date: Oct 2003 Last On: 06-07-2008 10:26 PM	You need washers. Most likely the burner is not sitting properly inside the housing. __________________

08-19-2004, 01:17 PM	#3 (permalink)
Sal Location: Windsor Posts: 2,231 Join Date: Oct 2003 Last On: 11-21-2008 04:46 PM Vehicle: 07 Dakota 2nd Vehicle: 02 Celica GTS	It has like 4-5 rubber washer already on it. Trevor from VD installed them on the guy's car i bought them off. __________________ Let it not be said dat I iz a man dat does not care.

08-19-2004, 02:21 PM	#4 (permalink)
DaksGT Location: Monaco Posts: 5,023 Join Date: Oct 2003 Last On: 06-07-2008 10:26 PM	Aim them then. __________________

08-19-2004, 06:41 PM	#5 (permalink)
Sal Location: Windsor Posts: 2,231 Join Date: Oct 2003 Last On: 11-21-2008 04:46 PM Vehicle: 07 Dakota 2nd Vehicle: 02 Celica GTS	ya i figure it is the only option left. I just hate doing it aming out hjeadlights are a pain in the ass __________________ Let it not be said dat I iz a man dat does not care.

08-19-2004, 06:52 PM	#6 (permalink)
DaksGT Location: Monaco Posts: 5,023 Join Date: Oct 2003 Last On: 06-07-2008 10:26 PM	Not at all, all you need is an 8mm and a wall. __________________

08-19-2004, 06:54 PM	#7 (permalink)
Sal Location: Windsor Posts: 2,231 Join Date: Oct 2003 Last On: 11-21-2008 04:46 PM Vehicle: 07 Dakota 2nd Vehicle: 02 Celica GTS	ya but getting it down in ther is a tight fit I find using my fingers is the best. I had to do my cuz's a while back and it was a pain in the ass __________________ Let it not be said dat I iz a man dat does not care.

10-18-2004, 11:54 PM	#8 (permalink)
TRD604 Posts: 5 Join Date: Oct 2003 Last On: 04-07-2005 10:53 PM	im having problems aiming mine. i used my fingers to turn the screw set thing. but didnt notice any changes __________________ 03 CELICA GTS TRD TEAM CELICA VANCOUVER WWW.CELICAGARAGE.COM

10-19-2004, 12:15 AM	#9 (permalink)
TRD604 Posts: 5 Join Date: Oct 2003 Last On: 04-07-2005 10:53 PM	nevermind...all fixed now.. __________________ 03 CELICA GTS TRD TEAM CELICA VANCOUVER WWW.CELICAGARAGE.COM

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search