Go Back   Celica Forums - Celispeed.com > Celica Generations > 5th Generation Celica (ST182/184/185) > 5th Gen Tech Info
User Name
Password
  Sign Up   Upload Pic(s)   Rules   Arcade   Search Today's Posts Mark Forums Read

aftermarket tach install

5th Gen Tech Info Useful information, repair manuals, diagrams, FAQs, and how-tos for the 5th Gen Celica.


Comment
 
LinkBack Article Tools Search this Article
aftermarket tach install
aftermarket tach install
subspec
06-11-2010
aftermarket tach install

installing a tachometer is very simple. It consists ot 2 simple steps: mounting and wiring. Both can be very tricky if you're unsure about what you're doing. These instructions are for any 90-93 Toyota Celica. Other Toyota vehicles may be similar.

Tools needed:

* Screwdriver (standard and Philips)
* Wire cutter
* Razor blade
* Drill
* Drill bits

Materials needed:

* 2 #8-32 x 1" bolts
* 2 #8-32 wing nuts

Step 1: Mounting
I didn't mount my tachometer on the left side because there is a vent I would end up drilling through. Instead, I mounted my tachometer in the center of the car to the right of the driver. The mounting instructions are for those who wish to mount their tachometer in the center of the car.

Pull out the center vent. Unplug the clock and the hazard plugs. You will be drilling three holes: 2 for the mounting screws and one for the wiring. Simply drill 2 holes large enough for the bolts to fit through and one hole large enough for 4 wires to fit through. You'll have to drill at an angle since the windshield is in the way. Mount the tachometer to your liking.

Step 2: Wiring
On the back of the tachometer, there are 6 wires: green, red, black, white, brown, and orange. Clip the brown and orange wires. Look at the back of the clock plug; there are 4 wires. You only need to be concerned about the gray, green, and white/black wire. Splice into each wire as follows:
Power: red on tach --> gray on clock plug
Ground: black on tach --> white/black on plug
Illumination: white on tach --> green on plug
Tach wire: green on tach --> black wire ON IGNITER
Under the dash, above the steering column, there is a brass-colored fitting that hides a hole in the firewall. Simply route the green tach wire through the hole and into the engine bay. If you have an aftermarket electronic ignition, such as MSD, GM, HEI, or Crane, connect the tach wire to the tach terminal.


i did not create this how to i took it off another celica website, celispeed nor am i responsible for dammage to your ignition system or after market tach.
Article Tools
Digg this Post!Add Post to del.icio.usBookmark Post in Technorati
Comment



Article Tools Search this Article
Search this Article:

Advanced Search


Similar Threads
Article Article Starter Category Comments Last Post
tach install alldafferm 5th Generation Celica (ST182/184/185) 14 07-07-2010 11:56 PM
how to install a walbro 255lph fuel pump subspec 5th Gen Tech Info 0 05-06-2009 10:02 AM
To install or not to install? still_stoned General Forum 1 10-26-2006 10:32 PM
Custom vs Aftermarket vs Stock exaust Stealth 7th Generation Celica (ZZT230/ZZT231) 2 09-23-2006 01:17 PM
Help with fast stereo install X24 General Forum 3 11-29-2004 03:36 PM

Posting Rules
You may not post new articles
You may not post comments
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


All times are GMT -4. The time now is 04:26 AM.


Powered by vBulletin
Copyright ©2000 - 2012, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.0.0 RC6

Article powered by GARS 2.0 RC2b ©2005-2006
Page generated in 0.21381 seconds with 18 queries